Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
This article down below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is seriously motivating. Don't bypass it.
Mounting a tub isn't exactly brain surgery, however it does need solid plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a brand-new one is additionally a reasonably tough job. If the old tub is conveniently obtainable, the job can move rapidly; if you have to open up a wall to eliminate the old bathtub and position the new tub, the task is a lot harder. In either instance, the job is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the brand-new one. Make sure you have certified on your own for the task as well as fit attempting it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your restroom if you have actually already gotten a brand-new bathtub and do not require to change the setup of your previous water system pipelines.
Your tools and product checklist should make up the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be rather troublesome because of the restricted access that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the taps. Have a fabric ready for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single taps from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, after that you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing hole in the bath/basin making certain that the washers are in place between the tap and the sink. Protect the tap in place with the producer supplied backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The former kind needs to be linked to the tap ends first, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Bathtub
Making use of the two wooden boards under its feet, position the tub in the required placement. The wood boards are handy in equally spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the spirit level reads level.
To install taps, fit the bottom of the furthest adaptable tap connector to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other faucet.
Activate the water and also inspect all joints as well as new pipework for leakages and also tighten them if needed. Fill up the tub and additionally inspect the overflow outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub needs to wait until the bathtub has actually been utilized a minimum of once as this will resolve it right into its final placement.
Getting ready for the Installment
First of all, the supporting structure supplied with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise reasonable to fit a supporting plate under the taps system to avoid strain on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bath satisfies the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to split a rigid seal, causing the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with moisture and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and also cartridges, and are capable of sealing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can fracture rather very early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally conveniently offered on the market. It is suggested to fit the ceramic tiles using water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid person who reads about A Step-by-Step Guide to Installing a Bathtub, I think sharing that chunk was really useful. Sharing is caring. Helping people is fun. We enjoy reading our article about How to Install a Bathtub.
Facing a flood? Call us! Report this page